Building a Bed–Part II

Fair warning, this is a long post.

When Ana White stained her bed, she used Varathane Weathered Wood Accelerator. We really liked the look of her bed, so we started researching this product. According to reviews, it seemed that quite a few people were ending up with a purple/blue color that they didn’t like. Given that feedback, we opted to research other wood aging stain products. Weatherwash had positive reviews, colors looked solid and it sounded like a good one to try.

After reading about the products on their site, I ordered the Pined Aging Stain and the Clear Maintenance Oil. The Oil is supposed to mellow the grey tones and bring out more of the warmer tones. I later bought the varnish because I originally misunderstood about how all three products work together.

Here is the headboard before (I know you can see the unstained pictures in the previous post, but here it is anyway), and after, one coat of the stain. Loved it!! It does look different on different wood types so do test spots on each type of wood first. There are three different woods in this headboard. .

Footboard and side rails.

It was dark outside when I applied a coat of oil, so I only have one bad picture of the before/after oil. I opted for the clear oil, but there is also a white oil, that lightens the stain. It totally beautified the wood even more, and I loved it!

Post oil footboard and rails. Ignore the areas where I needed to sand a little more than I realized and just look at the tones and how beautifully the grains show.

A few mornings ago, at my ridiculous 5:00 am get things done time, I used the varnish. Here is a garage shot of the headboard and footboard with stain, oil and varnish. We chose the flat varnish for this project, we weren’t looking for a super shiny finish.

Big excitement night before last, because…WE ASSEMBLED! Some of these pictures are from assembly night with poor lighting, and a few are from the next day, with the fancy camera.

One of my biggest fears was that the frame wouldn’t fit together well. It did! Because it is mostly heavy 2x4s and 2x6s, we had to carry everything upstairs separately and do all the assembly in the bedroom.

Fargo inspected our work as we progressed. He felt we did a solid job adding the cleats, the center support and had a good start on the slats. I am very glad we somehow ended up buying an extra 2×4. I cut the center support at the same 80″ as the cleats, but that ended up being too short. I would have been bummed if we’d had to wait until we could get out to buy another 2×4 to finish.

GAHHHHHH!!!!!! It’s done!!!!! I may have shed a tear of joy.

I wish the pictures could really portray how beautifully it turned out. If our room was a little larger, I might have been able to get better angles for entire bed shots, but the partials will have to do.

Following are some reflections on things I would probably do differently, besides sand a little more. I would make the frame an an inch or two higher, so the mattress sets up just a bit higher. For our bedroom, I’d probably take the top of the headboard down one panel, as our ceiling is fairly low. Our old mattress was about 4″ taller than the new one we bought (jury is still out on whether we like the new mattress), and if I had known this, I would have taken that panel from the top and put it on the bottom so no “pillow falling through” space existed. These are really just specific to our bedroom, and my learning curve.

Have I mentioned how proud I am of this bed?!?!? Honestly, one of my favorite parts was working with Tim. I’ve chronicled on this blog that empty nest has been hard for me. Tim has always had his outdoor hobbies, but I have been searching for something to feel passionate about. I have enjoyed baking and cooking and some of the other hobbies I’ve tried along the way, but I LOVED creating the workbench, the miter saw cart, the lumber storage cart and THIS BED. I love that Tim enjoyed working on all of these things with me. Although there is so much more to learn, I now have enough skill and knowledge base to do a lot on my own and keep me moving.  I greatly appreciate Tim’s participation and help when I want/need it, and I appreciate that he enjoys helping me. Can’t wait to get started on the next project!

 

 

 

2 thoughts on “Building a Bed–Part II

Leave a Reply

Your email address will not be published. Required fields are marked *